Mootek Technologies

• E1/FE1/Ethernet/V.35 Converters
• E1/FE1/V.35 to Fiber Converters
• Serial to E1 Converters

• 10/100M Ethernet to n x E1 Bridge
• 10/100M Ethernet to E1 (Framed E1) Converter
• V.35 to E1 (Framed E1) Converter
• E1 to Fiber Optic Modem
• RS485/422 to E1 Converter
• RS232 to E1 Converter
• PDH

• Integrated Transmitter, Receiver, and Jitter Attenuator for DS3, E3, and STS-1; 
• Have the function of E3/DS3/STS-1 interface loop back check, avoid the converter crashed because of interface loop return; 
• E3 Interface Ethernet Bandwidth is 34.368Mbit/s,DS3 Interface Ethernet Bandwidth is 44.736Mbit/s,DS3 Interface Ethernet Bandwidth is 51.84Mbit/s
• 4Channel 10M/100M Ethernet interface can isolate each other to realize communication independently; ??? Ethernet interface supports10M/100M, half/full duplex auto-Negotiation and AUTO-MDIX (crossed line and straightly connected line self-adaptable ); 
• Provide 2 clock types: E3/DS3/STS-1 master clock and E3/DS3/STS-1 line clock; 
• Have 3 Loop Back Mode: E3/DS3/STS-1 interface Loop Back (ANA)
• Ethernet interface Loop Back(DIG); E3/DS3/STS-1 interface Loop out (REM) 
• Provide 75  unbalance coaxial cable,B3ZS/HDB3 decoding, and loss-of-signal monitoring. ??? Have pseudo random code test function, easily line opened, can be used as a BER Tester
• AC 220V, DC-48V, DC+24V, DC Power and DC-48V/DC24V power has polarity automatic detection function, you can install the device without differentiation between positive and negative polarity.
• Ethernet Interface Interface Type: 10/100 Mbps, half/full duplex auto-negotiation Interface Standard: Compatible with IEEE 802.3, IEEE 802.1Q (VLAN) MAC Address Capability: 4096 Connector: RJ45, support AutoMDIX

• E1 interface Standard Comply with ITU-T G.703 
• Output tingle displace accord ITU-TG.735 advice 
• Input tingle limit accord ITU-TG.823 advice 
• Output tingle accord ITU-T G.823 advice 
• Frame format unframed 
• Interface rate 2.048Mbps×4=8.192Mbps 
• CRC checkout no 
• Port coding HDB3 
• Port transmission 2KM 
• Port protection 1500V electromagnetism isolate 
• Port connector 120 Ohm(RJ-45) and 75 ohm(BNC double coaxial) 
• Ethernet port 
• Interface Types 10/100BaseT, full/half duplex 
• Standards Compliance IEEE 802.3(support VLAN) 
• Bit Rate 10/100BaseT limited to Max 2.048 Mbps 
• Connectors: RJ45 (10/100 Base-T Electrical) 
• Line code 
• Manchester Encoding Connect line
• Connect PC with cross-over 
• Connect HUB/SWITCH with straight-through Environment
• Working temperature: -25 to 70C 
• Storage temperature: -40 to 85C 
• Humidity: Relative humidity 5% to 95% 
• Input power: 220VAC or -48VDC 

• Monitoring remote device from local device (having 2 row indicator LED, upper indicates local, lower indicates remote
• Based on self copyright IC. 
• Provides many kinds of clock ways: E1 master clock, and E1 line clock, V.35 master clock, V.35 external clock. 
• Having 3 loop back functions: E1 local loop, V.35 local loop, and let remote V.35 loop. 
• Having pseudo random code test function, can used as a 2M Protocol Analyzer 
• Support 120Ω/balance and 75Ω/unbalance impedance at the same time. 
• V.35 port supports hot plug, can connect with DTE or DCE. E1 interface Standard: compatible with G.703 standard. Rate: 2.048Mbps Coding: HDB3 Impedance: 75Ω (unbalance) and 120Ω (balance) Connector: BNC (75Ω), RJ45 (120Ω) Jitter Performance: According to G.742 and G.823 Clock: internal clock, Recovery clock. V.35 interface Interface:compatible with V.35 standard. Connector: DB15 Connect mode: DCE Clock: G.703 recovery clock, internal clock, V.35 external clock.

• High transmit efficiency, low transmit delay.
• Provide 1*V.35 channels and 2*10/100Base-TX and 1*100Base-FX interface.
• The length of Ethernet packet can be set, supporting huge packet. User can select IP protocol encapsulation or simplicity Ethernet type.
• Support VLAN setting,Ethernet ping function.
• Support package loss indicator function for V.35 transmission line.
• Have three Loop Back Mode: Ethernet interface Loop Back (ANA) 、
• V.35 interface Loop Back(DIG) 、 Command the remote V.35 interface Loop Back(REM) Have pseudo random code test function, easily line opened, can be used as a 2M BER Tester V.35 interface supports hot-plug, supports DTE or DCE device interconnection.
• Provide 3 clock types: Internal clock, External clock, slave clock;

MT-TDMoIP-V.35 is mainly used to transmit V.35 interface over IP network. It has V.35 interface, 2 UTP Ethernet port and 1*fiber Ethernet port. MT-TDMoIP-V.35 can connect TDM device and user’s low cost wireless or lineate Ethernet/IP configuration, without affecting the quantity. assures connecting to physical V.35 interface of any device seamlessly, It can be used in the communication system based on V.35, such as LAN, WAN, MAN and wireless network.

More Features : 

• Point to point or point to multi-points connections, satisfying different applications.
• High efficiency transmission, up to 90% bandwidth utility ratio.
• 10/100M Ethernet, full/half duplex auto-adapt, support auto-MDIX.
• When selecting network adaptation clock, it can resume the original clock accurately through TDM clock resumption mechanism, stable clock, little jitter and small excursion, conforming to ITU-T clock jitter and excursion standard.
• The device Support WEB management platform, online software upgrades, the host side can manage the work of each state machine equipment.

• Monitoring remote device from local device (having 2 row indicator LED, upper indicates local, lower indicates remote
• Based on self copyright IC. 
• Provides many kinds of clock ways: E1 master clock, and E1 line clock, V.35 master clock, V.35 external clock. 
• Having 3 loop back functions: E1 local loop, V.35 local loop, and let remote V.35 loop. 
• Having pseudo random code test function, can used as a 2M Protocol Analyzer 
• Support 120Ω/balance and 75Ω/unbalance impedance at the same time. 
• V.35 port supports hot plug, can connect with DTE or DCE. E1 interface Standard: compatible with G.703 standard. Rate: 2.048Mbps Coding: HDB3 Impedance: 75Ω (unbalance) and 120Ω (balance) Connector: BNC (75Ω), RJ45 (120Ω) Jitter Performance: According to G.742 and G.823 Clock: internal clock, Recovery clock. V.35 interface Interface:compatible with V.35 standard. Connector: DB15 Connect mode: DCE Clock: G.703 recovery clock, internal clock, V.35 external clock.

• Convert RS-232 interface to E1(2M unframed G.703) interface
• Support line recovery clock,local clock and equipment clock
• Support E1 port loop
• E1 (G.703 ) interface support 120ohm (RJ-45) and 75ohm (BNC double coaxial) SpecificationE1 interface
• Standard: Comply with ITU-T G.703
• Output tingle displace: Accord ITU-TG.735 advice
• Input tingle limit: Accord ITU-TG.823 advice
• Output tingle: Accord ITU-T G.823 advice
• Frame format: Unframed
• Interface rate: 2.048Mbps±50ppm
• CRC checkout: No
• Port coding: HDB3
• Port transmission: 2KM
• Port protection: 1500W surge protection, 15KV ESD protection
• Port connector: 120 Ohm(RJ-45) and 75 ohm(BNC double coaxial)
• RS-232 port
• Standards Compliance: EIA RS-232C
• Interface Types: RS-232(DB25 female)
• Signal: TXD, RXD, CTS, DSR, GND, DCD
• Baud Rate: 0~115.2Kbps
• Work mode: DCE
• Asynchronous serial, flucency transmission
• 600W surge protection, 15KV ESD protection
• Environment, Power and Dimension
• Working temperature: -25 to 70°C
• Storage temperature: -40 to 85°C
• Humidity: Relative humidity 5% to 95%